setup
aarch64-linux.pkgs-openclaw
· build #2758
· raw
1this derivation will be built:2 /nix/store/4mqvyddchzcavrn2ka8xlm7s9db7jndj-openclaw-2026.7.1-2.drv3error: build of '/nix/store/4mqvyddchzcavrn2ka8xlm7s9db7jndj-openclaw-2026.7.1-2.drv' on 'ssh-ng://nix-remote-builder@bld3.m.ntd.one' failed: Cannot build '/nix/store/4mqvyddchzcavrn2ka8xlm7s9db7jndj-openclaw-2026.7.1-2.drv'.4 Reason: builder failed with exit code 1.5 Output paths:6 /nix/store/mqpv7kfz38ir8n3mhdgz171xibblapj3-openclaw-2026.7.1-27 Last 25 log lines:8 > [tsdown-build] still running pid=1086; no output for 30s9 > [tsdown-build] still running pid=1086; no output for 60s10 > [tsdown-build] still running pid=1086; no output for 30s11 > [tsdown-build] still running pid=1086; no output for 30s12 > [tsdown-build] still running pid=1086; no output for 30s13 > [tsdown-build] still running pid=1086; no output for 30s14 > [tsdown-build] still running pid=1086; no output for 60s15 > [tsdown-build] still running pid=1086; no output for 60s16 > [tsdown-build] still running pid=1086; no output for 60s17 > [tsdown-build] still running pid=1086; no output for 60s18 > [tsdown-build] still running pid=1086; no output for 30s19 > [tsdown-build] still running pid=1086; no output for 30s20 > [tsdown-build] still running pid=1086; no output for 30s21 > [tsdown-build] still running pid=1086; no output for 60s22 > [tsdown-build] still running pid=1086; no output for 30s23 > [tsdown-build] still running pid=1086; no output for 30s24 > [tsdown-build] still running pid=1086; no output for 30s25 > [tsdown-build] still running pid=1086; no output for 30s26 > [tsdown-build] still running pid=1086; no output for 30s27 > [tsdown-build] still running pid=1086; no output for 30s28 > undefined29 > ERR_PNPM_RECURSIVE_EXEC_FIRST_FAIL Command was killed with SIGKILL (Forced termination): tsdown --config-loader unrun --logLevel warn --no-clean30 > [build-all] tsdown failed after 1259.8s31 > [build-all] phase timings: total 1279.6s; slowest tsdown (failed) 1259.8s; plugins:assets:build 19.8s32 > ELIFECYCLE Command failed with exit code 1.33 For full logs, run:34 nix log /nix/store/4mqvyddchzcavrn2ka8xlm7s9db7jndj-openclaw-2026.7.1-2.drv35error: Cannot build '/nix/store/4mqvyddchzcavrn2ka8xlm7s9db7jndj-openclaw-2026.7.1-2.drv'.36 Reason: builder failed with exit code 1.37 Output paths:38 /nix/store/mqpv7kfz38ir8n3mhdgz171xibblapj3-openclaw-2026.7.1-2